Hi again,
This is similar to my previous answer.
In this case, I think here you are setting too many resources. Since
your X values are equally-spaced, you don't want to set the "sfXArray"
resource. Since your Y values are not equally-spaced, you don't
want to set the "sfYCStartV" and "sfYCEndV" resources.
With that in mind, remove the following lines from your code:
NhlRLSetFloat(srlist,NhlNsfYCStartV, 5);
NhlRLSetFloat(srlist,NhlNsfYCEndV, 21);
NhlRLSetIntegerArray(srlist,NhlNsfXArray, XArray, 5);
and try again.
--Mary
On Sun, 20 Mar 2005, p yg wrote:
> Good everyone,
> I'm contouring a 5x5 points grid of data. The Y axis is non-equal interval
> as follows,
> YArray[5] = { 21,
> 18,
> 15,
> 10,
> 5 }
>
> that is, in Y axis, the interval from 5 to 15 is 5, while the interval from
> 15 to 21 is 3.
> The X axis is equal interval as follows,
>
> XArray[5] = { 0, 10, 20, 30, 40}
>
> My data is data[5][5] = { 10, 10, 10, 10, 10,
> 20, 20, 20, 20, 20,
> 30, 30, 30, 30, 30, 40, 40, 40,
> 40, 40,
> 50, 50, 50, 50, 50 };
>
> I want the contour as follows, in which the interval is not equal,
> (1)
> 50 50 50 50 50
> .
> .
> .
> 40 40 40 40 40
> .
> . .
> 30 30 30 30 30
> .
> .
> .
> .
> .
> 20 20 20 20 20
> .
> .
> .
> .
> .
> 10 10 10 10 10
> but I get the unwanted contour from my code as follows, in which the interval
> is equal, (2)
> 50 50 50 50 50
> .
> .
> .
> .
> 40 40 40 40 40
> .
> . .
> .
> 30 30 30 30 30
> .
> .
> .
> .
> 20 20 20 20 20
> .
> .
> .
> .
> 10 10 10 10 10
> How to get the non-equal interval of Y axis?
>
> I get the unwanted (2) contour from blow code, but how can I get the (1)
> contour?
> NhlRLSetFloat(srlist,NhlNsfYCStartV, 5);
> NhlRLSetFloat(srlist,NhlNsfYCEndV, 21);
>
> NhlRLSetFloat(srlist,NhlNsfXCStartV, 0);
> NhlRLSetFloat(srlist,NhlNsfXCEndV, 40);
>
> NhlRLSetIntegerArray(srlist,NhlNsfXArray, XArray, 5);
> NhlRLSetIntegerArray(srlist,NhlNsfYArray, YArray, 5);
> int icount[2];
> icount[0] = 5;
> icount[1] = 5;
> NhlRLSetMDFloatArray(srlist,NhlNsfDataArray,&data[0][0],2, icount);
> NhlCreate(&cndata,"cndata",NhlscalarFieldClass,appid,srlist);
>
> _________________________________________________________________
> 与联机的朋友进行交流,请使用 MSN Messenger: http://messenger.msn.com/cn
> _______________________________________________
> ncarg-talk mailing list
> ncarg-talk@ucar.edu
> http://mailman.ucar.edu/mailman/listinfo/ncarg-talk
>
_______________________________________________
ncarg-talk mailing list
ncarg-talk@ucar.edu
http://mailman.ucar.edu/mailman/listinfo/ncarg-talk
This archive was generated by hypermail 2b29 : Sun Mar 20 2005 - 13:34:56 MST